Request a Quote
≈200,000 lbs / month

10-20 Mesh Crumb Rubber

Roughly 200,000 pounds of 10-20 mesh every month. The go-to granule for turf infill, molded mats and surfacing, on a schedule you can build a production plan around.

Close-up of 10-20 mesh crumb rubber granules

What 10-20 mesh is

10-20 mesh crumb rubber passes a No. 10 sieve (2.00 mm opening, about 0.079 in) and is mostly retained on a No. 20 sieve (850 µm, about 0.033 in). In plain terms: granules roughly the size of coarse sand, about 1 to 2 millimeters across.

It's the most common "granule" grade in the crumb rubber business because it sits right where a lot of applications want to be. It's big enough to give bounce and drainage, and small enough to pack and bind well.

10-20 mesh crumb rubber granules resting on a steel test sieve screen
10-20 mesh granules on a test sieve. Gradation is measured by ASTM D5644.

Supply: about 200,000 lb a month

We produce roughly 200,000 pounds of 10-20 mesh per month. That's about five truckloads a month at typical dry-van weights. You can buy it as:

  • A one-time load for a project
  • A recurring program with fixed monthly or bi-weekly loads
  • An annual allocation split across your season

If you're running a turf, mat or surfacing line and you're tired of suppliers going dark in peak season, this is the conversation to have now.

Where 10-20 mesh goes

Synthetic turf infill

The New York State Department of Health describes turf crumb as granules "ranging from about one-sixteenth to one quarter inch," applied at two to three pounds per square foot. One-sixteenth of an inch is about 1.6 mm, right inside the 10-20 range. Many turf systems also use 8-16 mesh. Your system manufacturer's spec decides. More on our turf infill page.

Molded mats, pavers and flooring

Stall mats, gym tiles, pavers and wheel chocks are commonly bonded from 10-20 mesh with a polyurethane binder. Huntsman's published guidance for its MDI binder lists 3 to 10 percent binder by weight for smaller molded products, and 5 to 6 percent for molded cylinders. See molded products.

Playground and poured-in-place base

Poured-in-place systems typically use a bound base course of recycled rubber granules under a wear layer. Installers follow ASTM F2479 guidance, and finished surfaces are tested to ASTM F1292 for impact attenuation. See playground surfacing.

Asphalt rubber

Wet-process asphalt rubber uses coarser GTR than terminal blends. FHWA-HIF-20-043 puts the typical maximum particle size at about 1.5 mm (15 mesh), so a 10-20 product usually needs to be checked against the agency gradation before it goes into a binder. The spec decides.

Worked examples

Example 1: Infill for a football field

A regulation football field, end zones included, is 360 ft × 160 ft = 57,600 sq ft. At NYSDOH's 2 to 3 lb/sq ft:

  • Low end: 57,600 × 2 = 115,200 lb
  • High end: 57,600 × 3 = 172,800 lb
  • That's about 58 to 87 supersacks, or 3 to 4 truckloads

Real fields have run-off areas and system-specific infill depths. Use your system spec, but this tells you one month of our 10-20 output covers a full field.

Example 2: A stall-mat molder

A molder blends 10-20 crumb with polyurethane binder at 8% by weight (inside Huntsman's published 3-10% range for smaller molded products). For every 10,000 lb of finished mix:

  • Binder: 10,000 × 8% = 800 lb
  • Crumb: 10,000 − 800 = 9,200 lb of 10-20 mesh, about 4.6 supersacks

At 200,000 lb a month of crumb, that molder can run about 217,000 lb of finished mats a month on our 10-20 alone. Your binder supplier sets the actual ratio.

Lock in a monthly 10-20 program. Send grade, volume, delivery city/ZIP and your target price.

Request a Quote

Spec sheet

Spec sheet · RE-1020
Nominal size10–20 mesh
Full sieve distributiontypical ASTM D5644: ≤5% retained on No.10; zero on No.8. Full curve confirmed per lot.
Sieve standard / test methodASTM D5644 (lot sieve report on request)
Residual steel (max)typical ≤0.10% by weight (ASTM D5603)
Fiber (max)Production target ≤0.01% by weight (ASTM D5603)
Moisture (max)typical ≤1.0% by weight (ASTM D5603)
Specific gravitytypical ~1.15
Source / classificationtypical recycled passenger and/or truck tires · ground rubber (ASTM D5603)
Availability≈200,000 lbs per month — schedule confirmed at quote
PackagingSupersacks / bulk bags, with or without pallets · typical ~2,000 lb net per sack (confirmed on quote). Gaylords or loose bulk on request.
Minimum ordertypical one supersack (~2,000 lb) · truckload programs preferred
Lead timetypical 3–10 business days for in-stock grades; allocation confirmed at quote

typical = representative or industry-standard value, confirmed per lot and in your written quote. Mesh labels alone don't describe the full distribution.

Download the 10-20 mesh PDF data sheet.

Packaging and freight

Supersacks with or without pallets, typically around 2,000 lb net each. Truckloads typically run 40,000-44,000 lb in a 53-ft dry van. FOB Central Ohio or delivered to your door. See supersack shipping.

Frequently asked questions

What size are 10-20 mesh granules in inches?

They pass a 2.00 mm (0.079 in) opening and are mostly held on an 850 µm (0.033 in) opening. Call it about 1/32 to 5/64 inch.

Is 10-20 mesh good for turf infill?

It's one of the most common turf infill sizes. NYSDOH describes turf crumb as roughly 1/16 to 1/4 inch. The system manufacturer's spec has the final say.

Can I set up a monthly delivery schedule?

Yes. That's what our 10-20 production is built for. Tell us your loads per month and delivery window.

Does 10-20 have wire or fiber in it?

Wire and fiber are removed in processing. Limits for residual steel and fiber are on the spec sheet and confirmed per lot. If you have tighter limits, send them.

10-20 versus 8-16, which should I buy?

8-16 is coarser (passes 2.36 mm). Turf and molded systems specify one or the other. See our mesh guide or just send your spec.

Sources: NYSDOH, Crumb-Rubber Infilled Synthetic Turf Athletic Fields fact sheet (health.ny.gov); Huntsman SUPRASEC® MDI for rubber crumb molded applications sell sheet; FHWA-HIF-20-043 (2020); ASTM F1292, F2479; ASTM E11 sieve openings.

Need crumb rubber
by the truckload?

Send your grade, quantity and delivery ZIP or export destination. We'll review availability, packaging and freight, then come back with a written quote.

Request a Quote CallEmail