What "mesh" means
A mesh number refers to a standard test sieve. In the U.S., sieve openings are set by ASTM E11. Higher number, smaller opening. A No. 10 sieve has a 2.00 mm opening; a No. 40 has 425 µm; a No. 80 has 180 µm.
When someone says "10 mesh rubber," they mean rubber that passes a No. 10 sieve. When they say "10-20," they mean it passes No. 10 and is mostly caught on No. 20. When they say "30-minus," they mean it passes No. 30, with everything finer included.
Mesh-to-millimeter chart
| Sieve No. (mesh) | Opening | Approx. inches |
|---|---|---|
| No. 6 | 3.35 mm | 0.132 in |
| No. 8 | 2.36 mm | 0.093 in |
| No. 10 | 2.00 mm | 0.079 in |
| No. 14 | 1.40 mm | 0.055 in |
| No. 16 | 1.18 mm | 0.046 in |
| No. 20 | 850 µm | 0.033 in |
| No. 30 | 600 µm | 0.024 in |
| No. 40 | 425 µm | 0.017 in |
| No. 50 | 300 µm | 0.012 in |
| No. 80 | 180 µm | 0.007 in |
| No. 100 | 150 µm | 0.006 in |
| No. 200 | 75 µm | 0.003 in |
Quick mental anchors:
- No. 10 (2 mm): coarse sand
- No. 20 (0.85 mm): medium sand
- No. 40 (0.425 mm): fine sand / table salt
- No. 80 (0.18 mm): flour-like powder
How ASTM defines a mesh product
ASTM D5603, Standard Classification for Rubber Compounding Materials—Recycled Vulcanizate Rubber, defines product size with two sieves:
- A zero screen, the next sieve up, on which nothing may be retained
- A designation screen, on which only a small maximum percentage may be retained
ASTM D5644 (the sieve-shaker test method) states the allowed retained maximum is 5% for products up to 850 µm (20 mesh), 10% for 850-150 µm (20 to 100 mesh), and 15% for 125-20 µm (120 to 635 mesh).
| Product designation | Zero screen (0% retained) | Designation screen | Max retained on designation screen |
|---|---|---|---|
| 10 mesh | No. 8 (2.36 mm) | No. 10 (2.00 mm) | 5% |
| 20 mesh | No. 16 (1.18 mm) | No. 20 (850 µm) | 5% |
| 30 mesh | No. 20 (850 µm) | No. 30 (600 µm) | 10% |
| 40 mesh | No. 30 (600 µm) | No. 40 (425 µm) | 10% |
| 80 mesh | No. 60 (250 µm) | No. 80 (180 µm) | 10% |
Summarized from ASTM D5603 Table 1 / ASTM D5644 §4.2. Buy the current standard from ASTM for the full table.
So under ASTM rules, a "30 mesh" product may have up to 10% held on the No. 30 sieve but nothing on the No. 20. That's tighter than a lot of loose trade talk.

Range grades vs. minus grades
Crumb rubber is sold two ways:
| Type | Example | What you get |
|---|---|---|
| Range (window) grade | 10-20, 8-16, 20-30, 6-10 | Material between two screens. Fines mostly removed. |
| Minus grade | 30-minus, 40-minus | Everything below a top size, fines included |
Range grades are more uniform; minus grades are usually higher volume and lower cost. Neither is "better." The application decides.
How to read a sieve report
A sieve report lists each screen and the percent retained (or passing). Here's a representative 30-minus curve, like the one on our 30-minus page:
| Sieve | % retained | Cumulative % passing |
|---|---|---|
| No. 30 (600 µm) | 12 | 88 |
| No. 35 (500 µm) | 23 | 65 |
| No. 40 (425 µm) | 18 | 47 |
| No. 50 (300 µm) | 22 | 25 |
| No. 80 (180 µm) | 17 | 8 |
| No. 100 (150 µm) | 4 | 4 |
| Pan | 4 | 0 |
What to look at:
- Top screen. Anything on the zero screen is oversize. Ask why.
- Where the bulk sits. Here, 63% is between 600 and 300 µm.
- Fines. Material through No. 80 and No. 100 drives binder demand, dust and caking.
- Test method. ASTM D5644 covers particles down to 90 µm. For powders finer than that, other methods are used.
Worked example: comparing two quotes
"Same" product, different curves
Two suppliers quote "30-minus." Supplier A's lot shows 4% through No. 100; Supplier B's shows 15%.
If you're molding with polyurethane binder, B's extra fines soak up more binder, so you may need more binder per pound of crumb to get the same strength. If you're making a terminal-blend asphalt binder, B's fines may react faster. Same label, different behavior.
Always compare sieve reports, not names.
Common grades and where they go
| Grade | Size range | Typical uses | Our page |
|---|---|---|---|
| 6-10 / 6-14 ABR | 3.35-2.0 / 3.35-1.4 mm | Thick molded goods, base courses | ABR |
| 8-16 | 2.36-1.18 mm | Turf infill, molded goods | 8-16 |
| 10-20 | 2.00-0.85 mm | Turf, mats, surfacing | 10-20 |
| 20-30 | 850-600 µm | Fine-faced molded goods, binders | 20-30 |
| 30-minus | <600 µm | Asphalt, molded faces, export | 30-minus |
| 40 mesh | ~425 µm and finer | Binders, sealants | 40 mesh |
| 80 mesh | ~180 µm and finer | Coatings, compounding | 80 mesh |
For size terms beyond crumb: ASTM D6270 calls particles up to 2 mm "ground rubber," up to 12 mm "granulated rubber," and 12-305 mm pieces "tire-derived aggregate."
Know your mesh? Get a quote. Send grade, volume, delivery city/ZIP and your target price.
Request a QuoteFrequently asked questions
What is 30-minus crumb rubber in millimeters?
It passes a 600 µm (0.6 mm) opening. Everything is 0.6 mm or smaller.
Is a higher mesh number finer or coarser?
Finer. Higher mesh numbers mean smaller sieve openings.
What does 10-20 mesh mean?
Passes a No. 10 sieve (2.00 mm) and is mostly retained on a No. 20 sieve (850 µm).
Which ASTM standard covers crumb rubber particle size?
ASTM D5644 is the test method; ASTM D5603 is the classification that uses it.









