Request a Quote
Guide · Choosing a grade

What Mesh Do I Need?

Start with the application, not the mesh number. This guide walks each end use to the grades it typically runs, with the published numbers behind them.

Recycled rubber shown from coarse chips to fine powder

The short answer

If you make... Start with Published basis
Wet-process asphalt rubber 10-20 to 30-minus (to agency gradation) FHWA: typical max ~1.5 mm (15 mesh), down to 40 mesh
Terminal-blend binder 30-minus, 40, 80 mesh FHWA: 30-80 mesh, 30-40 most typical
Dry-process mix 30-minus / 30-40 mesh FHWA: 30-40 mesh, ~10 lb per ton of mix
Stall mats, pavers, chocks 10-20, 8-16, ABR Coarse body; less binder demand
Gym tiles, rolled flooring 10-20 core + 20-30 or 30-minus face Clean surface
Turf infill 10-20 or 8-16 NYSDOH: ~1/16 to 1/4 inch granules
Poured-in-place base 10-20, 8-16, ABR Installer system spec
Crack sealant 30-minus, 40, 80 mesh Fine grinds disperse faster
Coatings, compounding 40, 80 mesh, finer Filler behavior
Export Whatever your buyers spec; 30-minus and 10-20 are common Well-understood grades

Now the reasoning, so you can defend the choice to your engineer or your boss.

Four questions that pick your mesh

1. Does the rubber need to react, bind, or just sit there?

  • React (asphalt binders): finer = faster. FHWA notes reaction time is a direct function of relative surface area.
  • Bind (molded goods, PIP): coarser = less binder per pound; finer = smoother surface but more binder.
  • Sit there (turf infill): size controls footing, drainage and how infill behaves in the fibers.

2. Is there a spec?

DOT jobs, turf systems and playground systems usually come with a gradation band. If there's a spec, the spec picks the mesh. Send it to us, and we'll match a lot.

3. What equipment touches it?

Spray tips, augers, feeders and molds all have a particle size they hate. Tell us yours.

4. What does the finished surface need to look like?

Coarse crumb shows. Fine crumb disappears. Many molders use both.

Recycled rubber shown from coarse chips to fine powder
Coarse to fine: each step down in size changes how rubber behaves.

By application

Asphalt

FHWA-HIF-20-043 gives the clearest published numbers:

  • Wet process (asphalt rubber): 10-22% GTR by weight of binder, typical max particle ~1.5 mm (15 mesh)
  • Terminal blend: 5-15% GTR, 30-80 mesh, 30-40 most typical ("30 minus rubber")
  • Dry process: 30-40 mesh at ~10% by weight of binder ≈ 0.5% of mix ≈ 10 lb per ton

Full breakdown on rubberized asphalt.

Molded products

Coarse granules (10-20, 8-16, ABR) for thick goods; finer (20-30, 30-minus) for faces. Huntsman publishes 3-10% binder by weight for smaller molded products and 5-6% for molded cylinders. See molded products.

Turf infill

NYSDOH: granules about 1/16 to 1/4 inch, applied at 2-3 lb per sq ft. That's 10-20 and 8-16 territory. See turf infill.

Playground surfacing

Coarse granules for bound base courses; the installed system is tested to ASTM F1292. See playground surfacing.

Sealants and coatings

30-minus for textured fills, 40 mesh for crack sealants, 80 mesh for fine dispersion. See sealants & coatings.

Tire-derived fuel

Not a mesh product at all. TDF is chip-sized (we ship nominal 1-inch-minus) to the facility's fuel spec. See TDF.

Worked examples

Example 1: "We make mats and want a smoother top"

Current: 100% 10-20 at 8% binder. Change: 80% 10-20 core, 20% 30-minus face.

  • Per 10,000 lb of crumb: 8,000 lb 10-20 + 2,000 lb 30-minus
  • Expect the face layer to need more binder than the core because of the finer particles. Test it.
  • Both grades ship on one truck.

Example 2: "Our terminal blend reacts too slowly"

Current: coarse 30-minus at 10% GTR. Option: move part of the dose to 40 mesh.

  • FHWA notes finer GTR reacts faster
  • Trial: 50/50 30-minus and 40 mesh at the same 10% total
  • For 200 tons of binder: 20 tons GTR = 20,000 lb 30-minus + 20,000 lb 40 mesh, one mixed truckload

Not sure? Send your process and we'll recommend a grade. Send grade, volume, delivery city/ZIP and your target price.

Request a Quote

Frequently asked questions

What mesh crumb rubber is best for asphalt?

It depends on process. FHWA reports terminal blends most often use 30-40 mesh, dry processes 30-40 mesh, and wet-process asphalt rubber coarser GTR up to about 1.5 mm.

What mesh is used for rubber mats?

10-20 mesh is most common, with 8-16 and ABR for thicker goods and finer grades for faces.

What size is turf infill crumb?

About 1/16 to 1/4 inch per NYSDOH; 10-20 and 8-16 mesh are common.

Can I order a custom mesh?

Yes. Send the target sieve curve, monthly volume and date.

Sources: FHWA-HIF-20-043 (2020); Huntsman SUPRASEC® MDI molded rubber crumb sell sheet; NYSDOH synthetic turf fact sheet; ASTM F1292.

Need crumb rubber
by the truckload?

Send your grade, quantity and delivery ZIP or export destination. We'll review availability, packaging and freight, then come back with a written quote.

Request a Quote CallEmail