Why freight matters so much
Crumb rubber isn't jewelry. It's a bulk industrial material, and like aggregate or salt, the cost to move it can be a big part of what you pay delivered. The good news: most freight savings come from planning, not haggling.
A few fixed facts shape everything below:
- Federal gross weight limit: 80,000 lb on the Interstate system (23 CFR 658.17), truck plus trailer plus cargo
- That typically leaves a dry van room for roughly 40,000-45,000 lb of payload, depending on the tractor and trailer
- Supersacks (bulk bags, FIBCs) commonly hold about 1,500-2,500 lb of crumb, depending on mesh and bag size
- Crumb is light for its volume, so some loads "cube out" (fill the trailer) before they "weigh out"

1. Buy full truckloads
The single biggest lever. A truck costs about the same to run whether it's half full or full, so a full truckload (FTL) spreads that cost over more pounds.
Example: half load vs full load
Say a lane costs the same flat rate per truck. Shipping 20,000 lb puts the whole rate on 20,000 lb. Shipping 42,000 lb puts the same rate on 42,000 lb: freight per pound drops by more than half.
If you'll use 42,000 lb within a few months and have dry storage, the full load is usually cheaper delivered.
2. Mix grades on one truck
Need 30-minus for asphalt and 10-20 for molding? Or a core grade and a face grade? Put them on the same truck in separate, clearly labeled sacks. One freight bill, two products. See our bulk buying guide.
3. Go floor-loaded, without pallets, when it makes sense
We ship supersacks with or without pallets.
- Without pallets: more room, lower weight, no pallet cost. Works if you have a forklift that can lift by the loops.
- With pallets: easier to move with a pallet jack, better for docks without forklifts, and needed for some warehouses.
If your site handles loop-lift sacks, floor loading can fit more product per truck. Ask us to quote both.
4. Have unloading ready
Detention (driver waiting time) and redelivery charges add up. Before the truck shows up:
- Forklift on site, with an operator
- Dock or flat, firm ground for a side unload
- Someone to sign the BOL and count sacks
- Receiving hours that match the delivery appointment
If you don't have a dock or forklift, tell us when you ask for a quote so we can price a liftgate or other option, rather than surprising the driver.
5. Schedule, don't rush
Expedited freight costs more. Recurring buyers who give us a forecast get trucks scheduled on normal lead times.
Example: a monthly program
A molder uses 80,000 lb of 10-20 a month. Instead of four 20,000-lb rush orders, they take two full truckloads a month on a fixed schedule. Fewer trucks, fewer receiving appointments, and the supply is planned.
6. Store smart so you can take bigger loads
Bigger orders only save money if you have room. Supersacks stack (follow the bag maker's stacking rating), and they need to stay dry. A covered area, a few pallets of dunnage, and first-in-first-out rotation let you take a full load instead of a partial.
7. Match the sack to your process
Sack size isn't just packaging; it changes how many fit in a trailer and how fast you can unload. Tell us:
- Your max forklift capacity
- Whether you need a discharge spout (bottom unload) or cut-open
- Your feeder or hopper opening
The right sack can mean more product per truck and less labor per pound.
8. Think about location
We ship from Central Ohio. That puts a lot of the Midwest, Northeast and Southeast within a day or two by truck. Buying closer to the source usually means fewer freight miles. Compare delivered prices, not FOB.
9. Export? Plan for containers
For overseas buyers, crumb ships in containers. Things to pin down:
- Container size (20 ft vs 40 ft) and payload limits for the lane
- Pallets: wood pallets for international shipping generally need ISPM 15 treatment and marking
- Documentation: commercial invoice, packing list, bill of lading and any import requirements of the destination country
- Incoterms: who pays what, and where the handoff happens
See export crumb rubber.
Want a delivered price on a full truckload? Send grade, volume, delivery city/ZIP and your target price.
Request a QuoteA quick checklist
- How many pounds this quarter?
- FTL or partial?
- Which grades can share a truck?
- Pallets or no pallets?
- Forklift, dock, receiving hours?
- Storage space for a full load?
- Delivery window?
- Who receives and signs?
Answer those in your quote request and you'll get the best freight rate we can give.
Hidden freight costs to watch for
The line-haul rate is only part of the bill. These extras show up after the fact if nobody plans for them:
- Detention. Drivers are typically allowed a set amount of free time to unload; after that, waiting time is billed by the hour.
- Liftgate and inside delivery. Needed when there's no dock or forklift. Price it in advance.
- Redelivery. If the receiver is closed or can't unload, the truck may have to come back another day.
- Limited-access locations. Construction sites, schools and farms can carry extra charges.
- Appointment changes. Rescheduling at the last minute can cost a truck order or a layover.
Each of these is avoidable with a clear delivery address, receiving hours, a contact phone number on the order and the right unloading equipment.
Receiving a load: a five-minute checklist
- Check the seal (if sealed) and the BOL number against your PO.
- Count sacks and match them to the packing list.
- Look for damage: torn bags, wet bags, crushed pallets.
- Note any problems on the BOL before the driver leaves, and take photos.
- Check labels and lot numbers, especially on mixed loads, and stage each grade separately.
If something's wrong, a note on the BOL and photos make it simple to fix.
Comparing quotes the right way
A cheap FOB price can turn into an expensive delivered price. When you compare suppliers, put the quotes on the same basis:
| Compare | Why |
|---|---|
| Delivered price per pound | Includes freight to your door |
| Payload per truck | More pounds per truck lowers freight per pound |
| Packaging | Pallets, sack size and spouts change handling cost |
| Lead time | Rush freight costs more |
| Lot data | Cheap material that fails your spec is the most expensive kind |
Example: two quotes
Supplier A quotes a lower FOB price but ships from far away, and the trailer carries fewer pounds because of pallet weight. Supplier B quotes a higher FOB price, ships from closer and floor-loads more sacks per truck. Divide each total delivered cost by the pounds delivered. The lower FOB price doesn't always win.
Freight for small buyers
Not every buyer needs a full truck. If you're a small molder, a landscaper or a shop testing a new product, a few ideas still help:
- Combine orders with your next scheduled delivery so you pay for one truck instead of two.
- Pick up yourself if you have a truck and trailer and are within driving distance. Ask about pickup hours and loading.
- Accept a flexible delivery window so the load can ride with other freight on the lane.
- Order a little more if storage allows, since freight cost per pound drops as weight goes up.
- Ask about less-than-truckload (LTL) pallets for small quantities. Supersacks on pallets ship LTL; floor-loaded sacks generally don't.
Freight and sustainability
Fewer, fuller trucks aren't just cheaper. They also mean fewer truck miles per pound of rubber delivered. If your company tracks shipping emissions or reports on recycled content, consolidating orders into full loads is one of the simplest improvements you can make, and it's easy to document with your bills of lading.
Talk to your supplier
The best freight savings come from a conversation, not a rate sheet. Tell your supplier how much you use, when you need it and how you receive it. A supplier who knows your operation can plan loads, mix grades and pick packaging that cuts your delivered cost every month.
Paperwork that keeps freight moving
Clean paperwork prevents delays at both ends. On every order, make sure the purchase order lists the full delivery address, the receiving contact and phone number, receiving hours, any appointment requirement, unloading equipment on site and whether pallets are required. We put the lot numbers and sack counts on the shipping documents so your receiving team can check the load quickly and your QC team can trace each sack back to its lot.
Frequently asked questions
How much crumb rubber fits on a truck?
Typically about 40,000-45,000 lb in a dry van, within the 80,000 lb federal gross limit. Some loads cube out first.
How much does a supersack of crumb rubber weigh?
Commonly about 1,500-2,500 lb, depending on mesh and bag size.
Do you ship without pallets?
Yes, supersacks with or without pallets.
Can I mix grades on one truck?
Yes, in separate labeled sacks.





