The one-sentence definition
Crumb rubber is scrap tire rubber reduced to granules or powder, with the steel and fiber removed, and screened to a defined particle size. You'll also hear it called ground tire rubber (GTR), crumb rubber modifier (CRM) when it goes into asphalt, or recycled vulcanizate particulate rubber, which is the formal name ASTM uses.
That last name tells you something important. Tire rubber is vulcanized: it has been cured with sulfur and heat into a crosslinked network. You can't melt it back down like plastic. What you can do is grind it, and the ground particles keep the toughness and elasticity of the tire they came from. That's why crumb rubber shows up in roads, mats, turf fields and playgrounds.
Why it matters: the size of the market
Crumb rubber isn't a niche. The U.S. Tire Manufacturers Association (USTMA) publishes a scrap tire management summary every two years. Its 2021 report found:
- Ground rubber became the largest U.S. scrap tire market, consuming roughly 28 percent of all scrap tires, about 1.41 million tons, or over 77 million tires
- Within ground rubber, molded and extruded products (mats, flooring and similar) consumed 485 thousand tons; rubber mulch 391 thousand tons; rubber-modified asphalt 141 thousand tons; and fine ground rubber for new tires, coatings, sealants and exports 79 thousand tons
- Sports surfaces, including synthetic turf fields and running tracks, grew 35 percent since 2019
USTMA's John Sheerin called the shift historic: since USTMA's first report in 1990, tire-derived fuel had been the top market. In 2021, crumb rubber caught it.
Step 1: From tire to shred
A scrap tire is a composite: rubber compounds, steel wire (in the bead and, in radials, the belts), and textile cord. The first job is to cut it down.
- Primary shredding rips whole tires into large strips or chips.
- Secondary shredding/granulating reduces those to smaller pieces, often an inch or less.
At this stage, a lot of material is pulled off for tire-derived fuel (TDF) or tire-derived aggregate (TDA). ASTM D6270 defines TDA as pieces generally 12 to 305 mm used in civil engineering. Our TDF is a nominal 1-inch-minus chip.

Step 2: Grinding to crumb
To get to crumb sizes, the chips go through further size reduction. There are two main methods:
Ambient grinding
Rubber is ground at or above room temperature, typically with cracker mills or granulators. The Rubberized Asphalt Foundation's glossary describes the result: "irregularly shaped, torn particles with relatively large surface areas," which is exactly what you want when rubber needs to interact with hot asphalt.
Cryogenic grinding
Rubber is frozen (often with liquid nitrogen) until it's brittle, then shattered. Particles tend to be smoother-faced. FHWA's 2020 report lists ambient and cryogenic as the two most common grinding processes, with wet grinding used less often.
Which one is "better" depends on the application. Ambient crumb's rough surface helps in binders and bonded products; your spec may say which method is acceptable.
Step 3: Getting the steel and fiber out
This is where good plants separate themselves from bad ones.
- Steel comes out with magnets, usually several stages of them as the rubber gets finer. Residual steel is a spec line item because wire fragments damage molds, knives and pumps, and nobody wants them in a playground.
- Fiber (polyester and nylon tire cord) is removed with air separators, screens and aspirators. Fiber balls ruin a sealant finish or a mat face.
The leftover amounts are what show up on a spec sheet as "residual steel" and "fiber." Agencies take them seriously. Arizona DOT's asphalt-rubber spec, for example, has allowed only 0.1 percent fabric in its Type A rubber and 0.5 percent in Type B.
Step 4: Screening into grades
The cleaned crumb goes over stacks of vibrating screens. Each deck pulls off a size fraction:
- Coarse cuts like 6-10 and 6-14 (often sold as ABR, all-black rubber)
- Granule grades like 8-16 and 10-20
- Mid cuts like 20-30
- Fine grades like 30-minus, 40 mesh and 80 mesh powder
Oversize goes back to the mill. The art is balancing the screens so the plant makes what customers buy, which is why some grades are always in stock (for us, 30-minus by the millions of pounds and about 200,000 lb a month of 10-20) and others are made to order.

Step 5: Testing and packing
Before it ships, crumb is tested. The core test is particle size distribution by ASTM D5644, a vibratory sieve-shaker method for particles 90 µm (170 mesh) and larger. The result is classified under ASTM D5603, which names a product by its mesh (a "zero screen" that retains nothing, and a designation screen that may retain only a small percentage) and by its source material.
Other common checks: residual steel, fiber, moisture and sometimes specific gravity (ADOT has specified 1.15 ± 0.05 for asphalt-rubber crumb).
Then it's bagged. Most bulk crumb ships in supersacks, woven bulk bags holding around 2,000 lb each, with or without pallets. A typical 53-ft dry van carries roughly 40,000-44,000 lb.
A little history: why roads got rubber
Rubber in asphalt isn't new. FHWA's TOPS guide recounts that in the mid-1970s the Arizona Department of Transportation sponsored rubber research and adopted ground tire rubber in pavement interlayers and chip seals, and later as a binder modifier in open- and gap-graded mixes. California, Florida and Texas followed.
Then Washington got involved. Section 1038(d) of the Intermodal Surface Transportation Efficiency Act of 1991 required states to use a minimum amount of crumb rubber in asphalt each year starting in 1994. The National Highway System Designation Act of 1995 eliminated that mandate. Some states dropped their programs; Arizona, California, Florida, Rhode Island and Texas kept going, according to FHWA.
California stuck with it hardest. FHWA reports that as of 2023, asphalt-rubber gap-graded mixtures made up about 35 percent of Caltrans' annual tonnage placed. Today the newer dry-process technologies are spreading across the Midwest, with FHWA listing projects in Illinois, Indiana, Wisconsin, Michigan and Ohio.
The lesson for buyers: rubber in roads survived the end of a federal mandate because it works, and the states that use it the most have the most detailed crumb specs. That's good news for anyone who wants clear acceptance criteria.
What makes "good" crumb rubber
When buyers ask us what separates good crumb from bad, the answer is always the same five things:
- A consistent sieve curve. Lot-to-lot variation is what breaks processes.
- Low residual steel and fiber. Measured, not promised.
- Dry material. Moisture foams hot asphalt and reacts with polyurethane binders.
- Known source. Passenger vs. truck tires, whole tire vs. tread. ASTM D5603 classifies by source for a reason.
- Honest paperwork. A lot report that actually changes from lot to lot, because real production does.
Worked example: from tires to truckloads
How big is a truckload, in tires?
USTMA reported about 1.41 million tons of scrap tires went to ground rubber markets in 2021, which it equated to over 77 million tires. That's roughly 36.6 lb of scrap tire per tire in USTMA's math (2,820,000,000 lb ÷ 77,000,000).
A 42,000 lb truckload of crumb therefore represents material from roughly 1,150 scrap tires' worth of tire weight, and more than that in actual tires, since steel and fiber are removed and not every pound of tire becomes crumb.
That's one truck. We ship several a week.
Where crumb rubber goes next
- Roads: wet-process asphalt rubber, terminal blends and dry-process mixes. See rubberized asphalt.
- Molded products: mats, tiles, pavers, wheel chocks. See molded products.
- Sports fields: turf infill. See turf infill.
- Playgrounds: poured-in-place base courses. See playground surfacing.
- Sealants and coatings: fine grinds. See sealants & coatings.
- Export: container loads to buyers worldwide. See export.
Common myths
"Crumb rubber is just shredded tires."
Shredded tires are TDF or TDA. Crumb is a cleaned, screened, tested product, ground far finer than shred.
"All 30 mesh is the same."
Two lots labeled 30-minus can have very different fines content. Compare sieve reports.
"Steel-free" means zero steel.
Every grade has some residual. The question is how much, measured how. Ask for the number.
"Crumb rubber can be melted and remolded."
It's vulcanized. It's bonded with binders or blended into other materials, not melted.
Ready to buy crumb rubber by the load? Send grade, volume, delivery city/ZIP and your target price.
Request a QuoteFrequently asked questions
What is crumb rubber made from?
Scrap tires, ground down after steel and fiber are removed. Some products specify passenger tires, truck tires or tread rubber.
What is the difference between crumb rubber and ground tire rubber?
In everyday use they're the same thing. "Crumb rubber modifier" (CRM) is the asphalt industry's term.
How is crumb rubber graded?
By particle size (mesh) using ASTM D5644 sieve testing, classified under ASTM D5603.
What is crumb rubber used for?
Molded products, asphalt, turf infill, playground surfacing, sealants, coatings and export markets, per USTMA's market breakdown.
Where can I buy crumb rubber in bulk?
Right here. We ship supersacks from Central Ohio. Request a quote.
Sources: FHWA TOPS Asphalt Rubber Gap-Graded Mixtures How-To (PDF); USTMA, 2021 US Scrap Tire Management Summary and press summary (ustires.org); Scrap Tire News, "Scrap Tire Market Ups and Downs," Nov. 1, 2022; FHWA-HIF-20-043 (2020); Rubberized Asphalt Foundation glossary; ASTM D5603-23, D5644-23, D6270; ADOT §1009 as reproduced in a 2012 specification summary.




