Request a Quote
Blog · Molding

Molded Rubber Production Math

Stall mats, gym tiles, wheel chocks, pavers: the product changes, the math doesn't. Crumb plus binder equals product. Here's how to plan it, buy it and keep the line fed.

Stack of recycled rubber stall mats on a pallet in a barn aisle

Why molders should care about the math

Molded and extruded products are the biggest single use of ground rubber in the U.S. The USTMA's 2021 scrap tire report put the segment at 485 thousand tons of scrap tires, up 25 percent from 2019. If you're one of the shops making that product, crumb is probably your largest raw-material line, and the binder is your most expensive one.

Get the ratio right and you make money. Get it wrong and you either waste binder or ship product that falls apart.

The basic recipe

Most bonded rubber products are made the same way:

  1. Crumb (one or more grades) is weighed into a mixer
  2. Binder, usually an MDI-based polyurethane prepolymer, is added and mixed to coat every granule
  3. Optional color granules (EPDM) or pigment go in
  4. The mix is loaded into a mold or a cylinder ("bun") mold
  5. It's compressed and cured (heat, moisture, time, depending on the system)
  6. Buns are peeled into rolls; molded parts are demolded and trimmed

What the binder makers publish

Binder levels aren't a secret. Huntsman's sell sheet for its SUPRASEC® MDI binders in molded rubber crumb applications says:

  • Molded cylinder applications: 5-6% binder by weight
  • Smaller molded products: 3-10% binder by weight

Your binder supplier will tune that for your system, but it's the right starting range for planning.

Molded recycled rubber wheel chocks, speed bump, pavers and curb stop
Wheel chocks, pavers, a speed bump and a curb stop, all bonded crumb.

Why particle size changes binder demand

Binder has to coat the surface of every granule. Smaller particles have far more surface area per pound, so the same binder dose spreads thinner on fine crumb than on coarse.

That's why:

  • Coarse grades (ABR, 8-16, 10-20) sit toward the low end of the binder range
  • Fine grades (20-30, 30-minus) need more binder for the same strength
  • Fines in a coarse grade quietly raise your binder bill. A 10-20 lot with a lot of material through No. 30 behaves like a finer product

The fix: spec a fines limit, not just a mesh label, and ask for the lot's sieve report every time. See crumb rubber specs explained.

Moisture: the silent problem

Isocyanate binders react with water. Moisture in the crumb competes with the reaction you actually want, which can mean foaming, weak bonds or slow cure, depending on the system. Crumb is mostly dry out of the plant, but sacks stored outside or on wet floors pick up water.

  • Put a moisture limit in your spec (our typical is ≤1.0%)
  • Store sacks dry, under cover, off the floor
  • First in, first out

Worked examples

Example 1: 4×6 stall mats at 8% binder

A shop makes 4 ft × 6 ft stall mats from 10-20 mesh at 8% binder, inside Huntsman's 3-10% range for smaller molded products. Plan by weight of finished mix:

Monthly finished mix Binder (8%) 10-20 crumb (92%) Supersacks (~2,000 lb)
50,000 lb 4,000 lb 46,000 lb ~23
100,000 lb 8,000 lb 92,000 lb ~46
200,000 lb 16,000 lb 184,000 lb ~92

At 200,000 lb of mix a month, you'd use nearly all of the ~200,000 lb of 10-20 we produce monthly. Lock in allocation before your peak.

Example 2: Rolled gym flooring from buns

A flooring maker molds cylinders at 5.5% binder (Huntsman's 5-6% range for cylinders), with a 10% EPDM color fleck. Per 40,000 lb of buns:

  • Binder: 2,200 lb
  • EPDM fleck: 4,000 lb
  • Crumb: 40,000 − 2,200 − 4,000 = 33,800 lb of 10-20, about 17 supersacks

One truckload of crumb makes a bit over one truckload of buns.

Example 3: Two-layer wheel chocks

Body: 6-10 ABR. Face: 30-minus, 15% of the crumb. Binder: 6% overall. 20,000 lb of chocks per month:

  • Crumb = 20,000 × 94% = 18,800 lb
  • 30-minus = 2,820 lb; ABR = 15,980 lb
  • Expect the face layer to want more binder than the body; many shops mix the layers separately

Both grades ship on one truck in separate, labeled sacks.

Example 4: What 2 points of binder are worth

A shop running 100,000 lb of mix a month at 9% binder tests 7%:

  • Binder drops from 9,000 lb to 7,000 lb, a 2,000 lb monthly reduction
  • Crumb rises from 91,000 to 93,000 lb
  • Multiply the 2,000 lb by your binder price, minus 2,000 lb at your crumb price: that's the monthly saving if the product still passes your tests

Coarser, cleaner crumb with fewer fines is what makes lower binder possible. Test before you commit.

Choosing grades by product

Product Common grades Notes
Stall and trailer mats 10-20, 8-16, ABR Thick and tough
Gym tiles 10-20 core, 20-30 / 30-minus face Clean wear surface
Rolled flooring 10-20 (+ EPDM fleck) Cylinder molding
Pavers 10-20, 8-16 Drainage and bulk
Wheel chocks, curb stops, speed bumps ABR, 8-16 Mass and resilience
Anti-fatigue and fine-faced mats 30-minus, 40 mesh Smooth finish

Buying for a molding line

  1. Buy by the month, not the load. Give your supplier a 3-6 month forecast.
  2. Mix grades on one truck. Core and face grades together cut freight.
  3. Demand lot data. Sieve curve, steel, fiber, moisture on every lot.
  4. Inspect sacks on arrival. Torn or wet sacks go to the side.
  5. Keep a retained sample from each lot for at least as long as your product warranty.

We hold millions of pounds of 30-minus and produce about 200,000 lb a month of 10-20, with ABR, 8-16 and 20-30 available or made to order. That's built for molders.

Running a molding line? Price a monthly program. Send grade, volume, delivery city/ZIP and your target price.

Request a Quote

Running a trial before you switch suppliers or grades

Changing crumb source is one of the riskiest things a molding plant does, because small differences in particle shape, fines and moisture show up as density, strength or surface changes. A disciplined trial takes the guesswork out:

  1. Get a sample with its sieve report. Compare it to the lot data from your current supplier, not just the mesh label.
  2. Check moisture on arrival, before it goes near the binder.
  3. Run a small batch at your current binder level and recipe. Change one thing at a time.
  4. Measure what matters to your customer: thickness, density, tensile or tear if you test it, surface finish and edge quality.
  5. Run a second batch at a lower binder level if the first passes. That's where coarse, clean crumb can pay off.
  6. Approve a full lot only after the trial product passes, then keep a retained sample from that first lot.

How to read a lot report as a molder

The numbers on a sieve report tell you how the crumb will behave in the mixer:

  • Percent passing the bottom screen of your grade is your fines content. For a 10-20 grade, watch what passes No. 30. More fines means more binder demand.
  • Percent retained on the top screen tells you about oversize. Oversize can create lumps on the surface of thin goods.
  • Residual steel matters for appearance and for wear on tooling.
  • Fiber creates fuzz and weak spots in thin goods and can ball up in the mixer.
  • Moisture affects cure, as covered above.

Track these numbers lot by lot in a simple spreadsheet. After a few months you'll see which lots ran best and you'll be able to set your incoming specification with confidence.

Inventory planning for a molding line

Crumb inventory is cheap insurance compared with an idle press. A simple approach:

  • Calculate your average weekly crumb use from production records.
  • Hold two to four weeks of supply on site, depending on how reliable your freight lanes are.
  • Set a reorder point at one truckload plus your normal lead time in weekly use.
  • Place a standing monthly order for your core grade and adjust quantities with a phone call or email.

Example: reorder point

A plant uses 25,000 lb of 10-20 a week. Lead time is one week, and a full truck brings about 42,000 lb. Reorder point = 25,000 (one week of use during lead time) + a 25,000 lb safety stock = 50,000 lb on hand. When inventory drops to about 25 sacks, call for the next truck.

The bottom line for molders

Binder is chemistry; crumb is geometry. Buy crumb with a tight, documented size distribution, keep it dry, and your binder level becomes something you can control and lower with testing instead of something you have to keep raising to cover for inconsistent rubber.

Frequently asked questions

How much binder goes into a rubber mat?

Huntsman publishes 3-10% by weight for smaller molded products and 5-6% for molded cylinders. Your system and testing decide.

What mesh crumb rubber makes the best mats?

10-20 is the most common granule, with coarser grades for thick goods and finer for faces.

Why do fines matter?

They increase surface area, which raises binder demand.

Can you hold allocation for my peak season?

Yes, that's what recurring programs are for. Tell us your monthly volume.

Sources: USTMA 2021 US Scrap Tire Management Summary (summary); Huntsman SUPRASEC® MDI for Rubber Crumb Molded Applications sell sheet; ASTM D5644-23.

Need crumb rubber
by the truckload?

Send your grade, quantity and delivery ZIP or export destination. We'll review availability, packaging and freight, then come back with a written quote.

Request a Quote CallEmail